Furnace Repair in Seattle and the Puget Sound
No heat, short cycles, strange noises, or a furnace that runs and runs without warming the house. We find what's actually wrong, tell you the price before we fix it, and check the safety controls while we're there.
- Licensed, Bonded & Insured
- Family-Owned, 25+ Years
- Free, No-Obligation Quote
Get Your Free Quote
Tell us about your project and we'll follow up with next steps — usually the same day.
Request Free InspectionCommon Furnace Problems
Most calls come down to a handful of causes.
- Igniter or flame sensor failures
- Blower motors and capacitors
- Clogged filters starving the system
- Control board and thermostat faults
i
How We Handle Repairs
Straight answers, no upselling.
- Diagnosis before any parts are swapped
- Repair priced before work starts
- Venting and safety checks on every call
- Honest advice on repair vs. replace
i
Everything You Need to Know About Furnace Repair
We test the furnace through a full cycle: thermostat call, ignition, flame, blower and shutdown. That tells us where it's failing, rather than guessing and replacing parts until something works.
Before we leave we check the flue and venting, the heat exchanger for visible cracks, the safety switches, and carbon monoxide at the appliance. A furnace that heats but vents poorly is more dangerous than one that doesn't heat at all.
If your furnace is old and the repair is expensive, we'll tell you plainly and price a replacement for comparison. The decision is yours.
Furnace Repair: Before and After
Drag the slider to compare the same space before and after the work.


Before You Call
Check the thermostat is set to heat and has batteries, the furnace switch is on, and the filter isn't clogged. A badly blocked filter can shut a furnace down on overheat.
If you smell gas, leave the house and call your gas utility from outside. Don't flip switches or try to relight anything.
Recent Furnace Repair Jobs
i📍 Canyon Park, Bothell
i📍 Eastgate, Bellevue
i📍 Hilltop, Tacoma
i📍 Loyal Heights, Seattle
i📍 Getchell, Marysville
i📍 Getchell, MarysvilleHow We Handle Furnace Repair
Diagnose
We test the system and find the actual cause, not just the symptom.
Quote
You see the repair and the price before any work starts.
Repair
We fix it, then check the safety controls and venting while we're there.
Confirm
We run the system through a full cycle before we call it done.
Often Done Together
Most projects involve more than one kind of work. These are the services homeowners most often pair with this one:
We work across Seattle and the Puget Sound, including Seattle, Tacoma, Bellevue, Kent, Everett, Renton, Federal Way, Kirkland. See the full service area.
What Puget Sound Homeowners Are Saying
Free Inspection, Written Quote
Every furnace repair job starts with a free look at the space and a written quote, so you know exactly what you're paying for before we start.
FAQ
How do I know if I should repair or replace my furnace? +
Age, repair cost and how often it's failing all matter. We'll give you both prices so you can decide.
Why does my furnace keep turning on and off? +
Short cycling is often a dirty flame sensor, a clogged filter, or an oversized furnace. We'll find which.
Do you service all brands? +
Yes, we work on all common furnace brands.
Are you licensed and insured? +
Yes. Attic Star is licensed, bonded and insured in Washington (contractor license ATTICSI795QZ), and our own crews do the work. We don't use subcontractors.
How much will it cost? +
It depends on the size of the space and the work involved. The inspection is free, and you get a written quote before anything starts.
Get Your Free Furnace Repair Estimate
Fill out the form and we'll follow up to schedule your free, no-obligation inspection — most homeowners hear back the same day. Prefer to talk now? Call us directly.
Get Your Free Estimate
Takes less than a minute — tell us about your project and we'll follow up the same day.
Get my Free Estimate